AMX RE-DM6 Spezifikationen PDF herunterladen (Seite 66)

Appendix A: AMX Lighting Curves

RE-DM4 and RE-DM6 RADIA Eclipse Dimmer Modules

FIG. 53 shows the output voltage of the RDM-HDC module. Curve 4 is primarily used for control of

Prescolite Intelect Ballast, using the RDM-HDC module. Its range is from 1 to 12 VDC.

Lutron FDB Curve (5)

FIG. 54 shows the output voltage of a dimmer. It quickly dims the high end and extends the mid-range

dimming control with a cut-off at 18 volts. This curve can be useful with two wire dimmable fluorescent

ballasts.

Relay turn on level = 1%

Dimming Range = 16 - 120 VAC.

FIG. 53 Curve 4 Voltage output in volts DC

FIG. 54 Curve 5 Voltage output in Volts RMS

FIG. 55 Curve 5 at 120V

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 89 90

Radia Eclipse Dimmer 1
Table of Contents 5
Radia Eclipse Dimmer Modules 9
RE-DM4 Specifications 10
Suggested Loads 10
Line-In Connections 11
RE-DM6 Specifications 14
Suggested Installation Loads 14
AMX Lighting Systems 17
Installation 19
LEFT SIDE FRONT RIGHT SIDE 20
SIDE VIEW 21
RDA-ENC6B 21
TOP VIEW 21
High-Voltage Connections 23
Connect to neutral block 24
Low-Voltage Connections 28
Position Value 30
Connecting Dry Closures 31
Failsafe Input 31
Emergency Input 31
Default Settings 32
Overview 33
Lighting System Link 33
Main Lighting System Page 34
Device Configuration Page 35
FIG. 32 Presets section 36
FIG. 34 New Preset button 37
Software 39
Preset Status 40
Lighting Systems Overview 41
Programming Commands 42
Channels 44
SEND_STRINGs 44
Ramp Dimmers Up 45
Ramp Dimmers Down 45
Stop Ramping Dimmer 46
Ramp Active Preset Up 46
Ramp Active Preset Down 46
Stop Ramping Preset 47
Recall Preset 47
Record Preset 47
Level Status 47
Set Curve 48
Curve Status 48
Set Low End 48
Low End Status 48
Dimmer Status 49
Set Default Level Time 49
Set Default Preset Time 49
Set Default Ramp Time 50
Ramp To Level 50
Undefine Dimmer 50
Phase Query 51
Version Query 51
Factory Default 51
SEND_COMMANDs 52
Ramp Preset Down (NEW) 53
Stop Ramping Preset (NEW) 53
Curve Status (NEW) 54
Set Low End (NEW) 54
Low End Status (NEW) 54
Reboot (NEW) 54
Ramp to Level 55
Undefine Dimmer (NEW) 55
Phase Query (NEW) 56
FIG. 38 Basic dimming curve 58
Curve Configuration 59
Standard Dimming Curve (1) 60
Economical Dimming Curve (2) 62
0-10VDC Curve (3) 63
Curve 3 at 120 VAC 64
Curve 3 at 240 VAC 64
Curve 3 output in volts DC 64
0-12VDC Curve (4) 65
Lutron FDB Curve (5) 66
FIG. 56 Curve 5 at 240 VAC 67
Advance Mark VII Curve (6) 68
12% Roll Off (7) 69
19% Roll Off (8) 71
33% Roll Off (9) 72
S-Curve #1 (A) 74
Log-Curve #1 (B) 75
Log-Curve #2 (C) 77
S-Curve #2 (D) 78
10% Off Curve (N) 79
Always OFF Curve (O) 80
Always ON Curve (F) 81
Curve F at 240 VAC 82
Curve R at 120 VAC 83
Curve R at 240 VAC 83
Curves 5 & B at 120 VAC 83
Curves 6 & C at 120 VAC 84
Curves A & D at 120 VAC 85
Curves A & D at 240 VAC 85
Appendix B: Troubleshooting 87
Hardware Issues 88
Increase Your Revenue 90

Kommentare zu diesen Handbüchern

Keine Kommentare

AMX RE-DM6 Spezifikationen Seite 66

Kommentare zu diesen Handbüchern