AMX NXD-435P Installationsanleitung PDF herunterladen (Seite 2)

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

1/10

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-2262-14 REV: B

5. Press the Device Number field to open the on-screen Device Number keypad

and enter a value for the panel (default is 32001).

6. Press the System Settings button to open the System Settings page.

7. From the IP tab, toggle the DHCP Static field to DHCP if it is not already set to

DHCP.

8. From the Master tab, toggle the Type field to Ethernet.

• Toggle the Mode field to URL.

• Enter both the System Number and IP Address of the target Master.

9. Enter a valid Username and Password if the target Master is secured.

10. Press the Back button and then press the on-screen Reboot button to save

any changes and cycle power to the panel.

Installation of the NXD-435P

The NXD-435P can be installed either directly into the (optional) CB-TP5I Rough-In

Box or another solid surface environment, using either solid surface screws or the

included locking tabs for different mounting options. For more information, please

refer to the NXD-430/435 Operation/Reference Guide, available at

www.amx.com.The NXD-435P is contained within a clear outer housing known as

the back box (FIG. 3). This back box is not removed when installing the device into a

wall or into a Rough-In Box.

Installing the NXD-435P into a wall

The NXD-435P comes with a clear plastic backbox (FIG. 3) designed to attach the

panel to most standard wall materials. This backbox has a locking tab on three of the

four faces (missing only on the face containing the space for the connections) to help

lock the backbox to the wall. These locking tabs are only extended AFTER the

backbox is inserted into the wall.

WARNING: When installing the backbox, make sure that the assembly is in the

correct position and in the correct place. Once the locking tabs are extended and

locked into place, removing the backbox may be difficult without having access to the

back of the wall or causing damage to the wall.

Note: In order to guarantee a stable installation of the NXD-435P, the thickness of

the wall material must be a minimum of .50 inches (1.27cm) and a maximum of .875

inches (2.22cm).

WARNING: The maximum recommended torque to screw in the locking tabs on the

plastic back box is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the

tab screws, such as with powered screwdrivers, can strip out the locking tabs or

damage the plastic back box.

1. Prepare the area by removing any screws or nails from the drywall before

beginning the cutout process.

2. Cut out the surface for the back box. Refer to the dimensions in the NXD-430/

435 Operation/Reference Guide, available from www.amx.com, for more

information.

CAUTION: Making sure that the actual cutout opening be slightly smaller than the

provided dimensions is highly recommended. This action provides the installer with a

margin for error if the opening needs to be expanded. Too little wall material removed

is always better than too much.

3. Remove the front bezel from the NXD-435P.

4. Disconnect the capacitive touch connector from the 10-pin plug on the

bezel.

5. Insert both connectors into their corresponding locations along the bottom of

the touch panel.

6. Test the incoming wiring by attaching the panel connections to their terminal

locations and applying power via the PoE Injector. Verify that the panel is

receiving power and functioning properly to prevent repetition of the

installation.

7. Thread the incoming Ethernet and mini-USB wiring (if mini-USB access is

desired) from their terminal locations through the surface opening. Leave

enough slack in the wiring to accommodate any re-positioning of the panel.

8. Push the back box into the wall opening. Insure that the locking tabs lie flush

against the back box.

9. Extend the locking tabs on the sides of the back box by tightening the screws

inside the box until snug. Not all of the tabs must be extended to lock the back

box in place, but extending a minimum of two tabs is highly recommended.

Apply enough pressure to the screw head to keep the box flush with the wall:

this ensures that the locking tabs will tighten up against the inside of the wall.

The back box is clear to allow visual confirmation that the tabs have been

extended and are gripping the wall, as well as in assisting with removal if

necessary.

NOTE: Do not disconnect the connectors from the touch panel. The unit must be

installed with the attached connectors before being inserted into the drywall.

10. Reconnect the capacitive touch connector to the 10-pin plug on the bezel.

11. Place the bezel back onto the device.

12. Reconnect the terminal Ethernet and USB to their respective locations on

either the Ethernet port or NetLinx Master.

Installing the NXD-435P into a Flat Surface using #4 screws

Three #4 mounting screws (not included) are secured through circular holes located

at the left and right sides of the NXD-435P. The most important thing to remember

when mounting the NXD-435P is that the outer frame (Mounting Tabs) must be

installed flush against the mounting surface.

• Refer to SP-2261-02 for detailed installation dimensions.

• Cutting out the surface slightly smaller than what is outlined in the installation

drawings in order to make any necessary cutout adjustments, is highly

recommended.

1. Prepare the area by removing any screws or nails from the surface before

beginning the cutout process.

2. Cut out the surface for the NXD-435P.

3. Remove the bezel from the NXD-435P.

4. Disconnect the capacitive touch connector from the 10-pin plug on the

bezel.

5. Thread the incoming Ethernet and USB wiring from their terminal sources

through the surface opening. Leave enough slack in the wiring to

accommodate any re-positioning of the panel.

6. Connect the Ethernet and USB connectors to their corresponding locations

along the bottom of the un-powered NXD-435P touch panel. The USB

connectors can be from either a USB extension cable or a wireless USB RF

transmitter.

NOTE: Do not disconnect the connectors from the touch panel. The unit must be

installed with the necessary connectors before being inserted into the solid surface.

7. Carefully slide the main unit into the cutout until the Mounting Tabs of the

NXD-435P lie flush against the wall.

8. Insert and secure three #4 Mounting Screws (not included) into the

corresponding holes located along the sides of the NXD-435P, using a

grounded Phillips-head screwdriver, until the unit is secure and flush against

the wall.

9. Reconnect the capacitive touch connector to the 10-pin plug on the bezel.

10. Place the bezel back onto the device.

11. Reconnect the terminal Ethernet and USB to their respective locations on

either the Ethernet port or NetLinx Master.

FIG. 3

NXD-435P backbox with closed and open locking tabs

Locking tabs - Closed

Locking tabs - Open

Locking tab screws

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

AMX NXD-435P Installationsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Touchscreen-Monitore AMX NXD-435P