AMX NI-3100 Spezifikationen Seite 30
- Seite / 160
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Initial Configuration and Firmware Upgrade
20
NetLinx Integrated Controllers- WebConsole & Programming Guide (FMv3)
Resetting the Factory Default System and Device Values
1. In NetLinx Studio, access the Device Addressing dialog (FIG. 4 on page 6) by either one of these two
methods:
Right-click on any system device listed in the Workspace and select Device Addressing.
Select Diagnostics > Device Addressing from the Main menu.
2. Click the Set Device/System to Factory Default button. This resets both the system value and device
addresses (for definable devices) to their factory default settings. The system information (in the OnLine
Tree tab of the Workspace window) refreshes and then displays the new information.
3. Click Done to close the Device Addressing dialog.
4. Click Reboot (from the Tools > Reboot the Master Controller dialog) and wait for the System Master to
reboot.
The STATUS and OUTPUT LEDs should begin to alternately blink during the incorporation. Wait until
the STATUS LED is the only LED to blink.
5. Press Done once until the Master Reboot Status field reads *Reboot of System Complete*.
6. Click the OnLine Tree tab in the Workspace window to view the devices on the System.
The default System value is one (1).
7. Right-click the associated System number (or anywhere within the tab itself) and select Refresh System.
This establishes a new connection to the specified System and populates the list with devices on that
system.
8. Use Ctrl+S to save these changes to your NetLinx Project.
By setting the system to its default value (#1), Modero panels that were set to
connect to the Master on another System value will not appear in the OnLine Tree
tab of the Workspace window.
For example: A Modero touch panel was previously set to System #2. The system is
then reset to its default setting of System #1 and then refreshed from within the
Workspace window. The panel will not reappear until the system is changed (from
within the System Connection page on the Modero) to match the new value and both
the Master and panel are rebooted.
- Last Revised: 5/25/2012 1
- Table of Contents 10
- About This Document 12
- Related Documents 13
- Using Zero Configuration 14
- Before You Start 15
- Device Addressing dialog 16
- WebConsole UI Overview 31
- Device Tree 32
- Device Network Settings Pages 33
- ZeroConfig Networking 34
- WebConsole - Security Options 35
- Login Rules 36
- User Name and Password Rules 36
- Allowed Special Characters 36
- Security - System Level 37
- Access Options 38
- Accepting Changes 39
- Configuring Settings 39
- System Security - Group Level 40
- Group Security Details Page 42
- System Security - User Level 44
- Deleting a User 46
- Compression Options 47
- WebConsole - System Options 49
- Diagnostic Options table 54
- Edit Options window 56
- Port Settings 59
- Server Port Settings 59
- SSL Certificate Options 61
- SSL Certificate Entries 62
- Import SSL Certificate window 64
- System - Manage License 68
- System - Manage NetLinx 69
- System - Manage Devices 71
- Manage Devices - Bindings 73
- Adding a User-Defined Device 77
- Editing Polled Port Settings 80
- Manage Devices - URL List 82
- Manage Devices - Log 85
- Manage Devices - Diagnostics 86
- NetLinx Programming 89
- Master SEND_COMMANDs (Cont.) 90
- Port: System 91
- RS232/422/485 Ports Channels 92
- IR / Serial Ports Channels 97
- IR RX Port Channels 97
- IR/Serial SEND_COMMANDs 97
- Input/Output SEND_COMMANDs 103
- I/O SEND_COMMANDs (Cont.) 104
- Overview 105
- Terminal Commands 107
- Terminal Commands (Cont.) 108
- ESC Pass Codes 125
- Setup Security Menu 127
- Security Options Menu 128
- Edit User Menu 129
- Edit Group Menu 129
- Telnet Diagnostics Commands 132
- Linux Telnet Client 133
- IPSec Config file 135
- Internet Key Exchange (IKE) 135
- SpdAddTunnel 138
- SpdAddBypass 139
- SpdAddDiscard 139
- SpdSetProp 140
- SpdSetProp (Cont.) 141
- SpdSetPropAttrib 143
- Manual Key Manager (MKM) 145
- IPSec Security Settings page 153
- Programming API 155
- CLKMGR_GET_ACTIVE_TIMESERVER 156
- (CONSTANT CHAR RECORD[]) 157
- Increase Your Revenue 160
Verwandte Produkte und Handbücher für Gateways / Controller AMX NI-3100
(40 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern