AMX TPI-PRO-2 Spezifikationen Seite 68
- Seite / 194
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
TPI-PRO/DVI Configuration Pages
66
TPI-PRO/DVI (Total Presentation Interface)
Configuring Incoming Video Signals
In the Video Settings page, you can select any of the available source inputs by selecting the corresponding tab
(Slot 1 - Slot 4) at the top of the page.
If the selected source input is receiving a video signal, this video is displayed in the Incoming Video Signal
Window. Use the video settings on the right side of the page to adjust the incoming video signal.
When using a a non-touch enabled monitor, the incoming video image often must be adjusted to fit into the
visible screen area. Refer to the Setting the Output Resolution section on page 34 for instructions on adjusting
the position and size on a non-touch enabled monitor.
When using a touch monitor, the TOUCH DRIVER selected should compensate for the visible area. If not,
continue with these steps.
1. Open the tab (Slot 1 - Slot 4) that corresponds to the Input that you want to adjust.
2. Press Input to cycle through the available Input Type options:
Setup - Video Settings Page (Cont.)
Incoming Video
Signal Window:
The video signal on the TPI-PRO/DVI Input that corresponds to the open tab is displayed in
this video button (Input 1 is displayed on the Slot 1 tab, Input 2 is displayed on the Slot 2
tab, etc).
Press inside the Incoming Video Signal Window to open the Full Screen Settings page.
Video
Parameters:
The Video Parameters (i.e. Brightness, Contrast, Saturation, etc.) presented on this page
depend on the Input Type assigned to the selected Input.
See the Video Parameters section on page 67 for descriptions of all possible Video
Parameters.
Default Settings: Press to reset all video settings to their default values.
Undo Changes: Press to disregard any changes made on the page since the last settings were saved.
Save Settings: Press to save all changes made on this page.
FIG. 65
Video Settings page (Slot 1 tab)
Video settings will vary
depending on the
source input type
Incoming video signal window
Press to cycle through the Input Types
- Operation/Reference Guide 1
- Total Presentation Interface 1
- Table of Contents 10
- Overview 11
- TPI-PRO Specifications 11
- Rack-Mounting the TPI-PRO 15
- VGA IN to S-Video Pinouts 18
- Wiring and Device Connections 19
- Connections Overview 20
- Front Panel Connectors 21
- Rear Panel Connectors 22
- USB (Type A) Input ports 24
- ETHERNET 10/100 (RJ-45) Port 24
- TOUCH INPUT (DB-9) Port 25
- AUDIO OUT Connector 26
- 12VDC PWR (Power) Connector 27
- Type A & Type B USB Ports 28
- Notes on USB Connections 28
- System Installation 29
- Touch Input via Touch Monitor 30
- Mouse Pass-Thru Control 31
- Configuring the TPI-PRO/DVI 35
- Setting the Output Resolution 36
- Resolution Setup page 37
- Calibrating the TPI-PRO/DVI 38
- FIG. 32 Protected Setup page 39
- Other Configuration Pages 40
- FIG. 41 System Settings page 45
- (FIG. 51) 53
- Manage System (System Number) 54
- System - Manage NetLinx tab 54
- Rebooting the TPI-PRO/DVI 56
- Resolution Setup Page 57
- Panel Information Page 58
- Calibrate Page 59
- Setup Page 60
- Setup Page (Cont.) 61
- Setup - Protected Setup Page 62
- Setup - Audio Settings Page 65
- Setup - Video Settings Page 66
- FIG. 64 67
- Video Parameters 69
- Video Parameters (Cont.) 70
- Input Resolution popup page 71
- Protected Setup Page 73
- Protected Setup Page (Cont.) 74
- G4 Image Caching 81
- Enabling Image Cache 82
- Clearing the Image Cache 83
- Checking Image Cache Status 83
- Protected Setup - Tools 84
- Using the Connection Utility 86
- NetLinx Programming 89
- Fixed Fonts and ID Numbers 91
- Slider/Cursor Names 91
- Border Styles By Name 92
- Border Styles By Numbers 93
- Text Effects Names 93
- SEND_COMMANDs 94
- Page Commands 95
- Page Commands (Cont.) 100
- "^" Button Commands 103
- Button Query Commands 122
- Button Query Commands (Cont.) 124
- Panel Run Time Commands 131
- Input Commands 137
- Input Commands (Cont.) 138
- Embedded Codes 141
- Panel Setup Commands 142
- Listbox Commands 143
- Data List Commands (Cont.) 144
- List View Commands 146
- List View Commands (Cont.) 147
- Dynamic Image Commands 149
- Text Area Input Masking 153
- Input Mask Character Types 153
- Input Mask Output Examples 155
- URL Resources 155
- Special Escape Sequences 156
- Terminal/Telnet Commands 157
- Upgrading Firmware 159
- System Settings page 163
- Using G4 Web Control 167
- Connection Details dialog 169
- G4 Authentication dialog 170
- Using Takenote™ 171
- TakeNote Menu Bar 172
- Drawing Annotation Tools 173
- Using the Select Object Tool 174
- Using the Save Tool 176
- Shape Options Menu Bar 177
- Inserting a Push-Pin Icon 178
- Inserting an Arrow Icon 178
- Text Annotation Tools 179
- Text annotations example 180
- Pen Options Menu Bar 181
- Clearing Annotations 182
- Canvas Options Menu Bar 182
- Working With Opacity Settings 182
- Session Tools 183
- Hiding TakeNote 183
- Hiding TakeNote Annotations 184
- AMX TakeNote web application 185
- Thumbnail Images 186
- FIG. 125 Preview Image 187
- FIG. 126 Download button 187
- Print button 189
- Delete button 189
- 5. Click Ye s to proceed 190
- Troubleshooting 191
- Appendix 193
Verwandte Produkte und Handbücher für Vernetzung AMX TPI-PRO-2
Vernetzung AMX NI-900 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Vernetzung AMX NXR-ZRP Spezifikationen
(2 Seiten)
(2 Seiten)
Vernetzung AMX RDM-HDC Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Vernetzung AMX MAX-MDL200 Spezifikationen
(60 Seiten)
(60 Seiten)
Vernetzung AMX NI-2100 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Vernetzung AMX MXTD-700 Spezifikationen
(2 Seiten)
(2 Seiten)
Vernetzung AMX ALD-H48 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Vernetzung AMX ALD-H48 Bedienungshandbuch
(48 Seiten)
(48 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern