AMX IRLIB Bedienungsanleitung PDF herunterladen (Seite 8)

KI-1856C Rauland RANGER

Head End—

Installation

Page 8 of 55 (Jun-98)

RAN[

]VS[

] Video Matrix Switchers

(Utah or AutoPatch)

Note: The

RAN

[xx]

[yy] is a

modular unit. The xx

and yy are variables

that refer to the

capacity of the

switch: xx=inputs

and yy=outputs.

RAN

[

]

[

] and AutoPatch Switchers are video matrix switches desi

ned to connect

stem in

uts (t

icall

media devices or locall

ori

inated broadcasts) to out

locations (t

icall

classrooms) in baseband

RANGER

stems. Switchers are also used

in mixed baseband/broadband s

stems as in

uts to modulators. Connections between

classrooms and the media center are controlled throu

h the

RANCPU

Control S

stem

Master Card, which interfaces to the Video Matrix Switch via an

RAN

232 connection.

The switch then connects to the source device or other audio/video in

uts throu

multi

lexer module (

RANAVMS2

)

ermittin

the use of a video-onl

switch. The

RAN

[xx]

[

] is available in increments of ten in

uts and ten out

uts. The AutoPatch

Switcher is available in increments of four in

uts and four out

uts. If the s

stem is

switched broadband s

stem, s

ecif

that the audio o

tion be included, and do not use the

RANAVMS

2 or the

RANAVDS

Parts Required

1 Interface cable (refer to drawing

2374 for the

RAN

[xx]

[yy] switch and

2395

for the Autopatch switch)

1 Power cord (supplied with the switch)

RAN232

Serial Control Card (see “

RAN232

” for more information)

Associated Equipment

RANCC16

Control Card Cage (see “

RANCC16

” for more information)

8 Mounting screws (

Part #

0439) and 8 washers (

Part #

0315) for

RAN

[

]

[

]

Installation

Typically the

RAN

[

]

[

] itself will not be set up in the field and the steps detailed

here will not need to be carried out by field personnel. These instructions are provided

for reference purposes.

Warning: Before

handling the

control card,

discharge static

electricity from

your clothes or

body by touching a

metal surface or

using a grounding

strap.

If it is not already mounted, mount the

RAN

[

]

[

] into the rack.

Remove the control card b

usin

the u

er and lower

lastic tabs. The card will

have two sets of

DIP

switches labeled “Baud Rate” and “Stat/Bus.” Usin

the

followin

illustration, set the

DIP

switches for Utah Scientific switchers accordin

The settin

rovided are for s

stems that have onl

one switch frame. The correct

Utah Scientific serial

ort settin

s are 9600 baud, even

arit

, 2 sto

bits, 7 data bits.

If you are adding additional frames, you must adjust the settings. Contact Rauland-

Bor

for more information. AutoPatch switchers do not have a settin

like this. The

default serial

ort settin

s, which are made in the software, are 9600 baud, no

arit

1 stop bit, and 8 data bits.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 54 55

Kommentare zu diesen Handbüchern

Keine Kommentare

AMX IRLIB Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software AMX IRLIB